How to Safely Remove 3D Prints After Finished: A Complete 2020 Guide

You spent hours searching for the right 3D model to print, wash up and print the image. Here lies the final stage of extracting the completed print from the board for building. Do you understand how to correctly do that? A lot of things, like the form of print bed you are using, the adhesives you already added, or whether you have any helpful resources available, rely on the right technique. This article will tell you how to safely remove 3d prints after finished.

To safely remove 3d prints, you require 3d printing safety tools. You also require proper 3d printing safety rules. For more information about 3d printers, click here.

remove 3d prints

How to Safely Remove 3D Prints After Finished?

Use Of Clean Glass Bed

The first item that you need to have the 3D printer is a glass printing pad before you begin to work on any venture. Glass offers the prints with a totally smooth and seamless layer to cling to, thereby guaranteeing absolutely seamless lower surfaces. It’s economical, easy to vacuum, and heats more uniformly than a printed aluminum sheet.

There are a number of online glass print beds available-just be sure you buy one that suits the building platform. Please ensure you thoroughly clean your glass bed with isopropyl alcohol whenever you begin a new print. This removes all fingerprint oils and any leftover glue from the past printing work. This easy planning act will help to strengthen bed stickiness and make it much easier to extract the print until you’re finished.

Adjustment Of Z-Setting

To remove 3d prints, proper adjustment of z-setting is required. This complies with 3d printing safety and 3d printing equipment. The objective is to make the print adhere to the building platform while changing the printer setup so that it stays steady during printing. You don’t want it to hold Quite long, though, that you eventually wind up with a print that’s too difficult to erase.

In deciding how well the base layer holds to the print bed, the original Z-setting of the printing funnel plays a major part. You would like to maintain the Z-setting around 70% to 80% of the first layer height as a general rule. To assist with bed binding, this adds just about enough stress to the first sheet.

Use Of A Flexible Print Bed

Actually, we said you were going to be using a glass printing bed. Glass is inexpensive and durable, but when it happens to print extraction, it doesn’t really help much. Because of just how quickly prints can be extracted from them, portable print beds have begun to become common in the past few years.

The benefit of having a flexible print bed is that it can be bent or twisted easily and the print pops straight off. A lightweight print sheet has so far proved to be the simplest method for print extraction currently available. You’re going to have to invest a lot longer on a magnetic display sheet than a glass bed of an equal size.

It’s very fragile as well, so when turning or bending it, you would need to be cautious. You would still want to stop using a spatula from a versatile printing pad to pry off something. This should be taken care of to remove 3d prints. Also, to remove 3d prints, proper 3d printing safety rules should be applied.

remove 3d prints

After Printing

Let The Print Cool Down
  • This should be kept in mind to remove 3d prints. After you’ve completed printing the upper surface of your framework, the first thing you have to do is watch. Allow the print to cool to room temperature. It might take as much time as one to two hours, based on the scale of the task and your printing heat.
  • If you’re lucky, that could be enough to shrink the plastic material as it cools down to make it jump off the printed bed without you wanting to connect it. If this is not the case, you are simply moving on to the next stages.
Trying To Force It Off
  • Even if the cooling process did not lead to the print flipping off the print bed, the print could still have partly removed and damaged the adhesive forces between both the bottom surface of the print and the print bed. By adding a bit of pressure yourself, you may just be able to resolve this sticky strength.
  • Trying to force, drag, or turn the print at the core is the easiest way to extract the print. When we’re doing this, be very patient. Without destroying the print, the level of power you can exert will rely on how large it is and the width of the covering. This is an experience test, but on the cautious side, you ought to error.
Cooling Down Further

This should also be kept in mind to remove 3d prints. If you didn’t do the job of bringing your print back to room temperature, so there was another widely utilized method you can do: put the entire print bed inside the freezer. Keep it for around an hour, and ideally the print could have eased sufficiently to extract it without any special equipment.

Rinsing with water

If, like a glue stick or hairspray, you have used a water-soluble additive on your print bed, so it just makes more sense to wipe it off with water afterwards. In some liquid, literally drench the entire print bed before the adhesive falls off.

remove 3d prints

Buying Guide

  • Price: Price is also an important factor. A number of options are available in the market and they all fall within a great affordable range.
  • Good features: The printer that you will be buying should have proper features. There must be best as well as safety features available.
  • Proper resolution: The 3D printer that you are buying should have proper resolution. That is very much important for good quality printing.
  • Know the thing before printing: Always make sure to have a clear idea about what you are printing. This is one of the biggest considerations of buying a 3D printer.

Frequently Asked Questions

What material is used for 3D printing?

Many different materials can be used for 3D printing, such as ABS plastic, PLA, polyamide (nylon), glass filled polyamide, stereolithography materials (epoxy resins), silver, titanium, steel, wax, photopolymers and polycarbonate.

What is a good resolution for 3D printing?

Formlabs advises erring on the side of thicker layers until the use small sections is required. Many commercial FDM printers assert regular print lengths of 0.1 – 0.3 mm while the Ultimaker 2, that is called a high-resolution 3D desktop printer, promises a layer height of 0.02 mm.

Do you need a heated bed 3D printer?

Heat beds are used because they dramatically improve print quality by keeping the extruded plastic warm and thus preventing warping. Warping is a common condition caused by plastic on the edges of the part cooling down at an uneven rate when compared to the plastic inside of the part.

Is it worth it to buy a 3d printer?

3D printing is great but for all it’s just not worth it. Most individuals waste a lot of money on 3D printers when just exporting a few pieces is really all they can do. Worse still, some people are buying a 3D printer just to figure out they don’t really like using it.

What material cannot be 3D printed?

The materials which are in low temperatures such as plastics, metals, and several types of pastes. The 3D printing process is a much-heated process if you use it in plastic, then the material will be destroyed and also can be dangerous.


You need to properly remove 3d prints as it is the last step of 3d printing. To properly remove 3d prints, you need proper 3d printing safety tools. Take extra care to remove 3d prints as forcing it off the print bed can cause more harm than good. Here, you can get more information on how to remove 3d prints easily and how it works.

Have Any Questions? Talk to our support team here.

Reset Password
Compare items
  • Total (0)
Shopping cart