17 reviews for Flashforge Adventurer 3 Lite 3D Printer
4.9out of 5
★★★★★
★★★★★
16
★★★★★
1
★★★★★
0
★★★★★
0
★★★★★
0
Write a review
Show allMost HelpfulHighest RatingLowest Rating
★★★★★
V***r –
And so let’s start with the fact that the delivery is declared 30 days. So the printer came in 5 days. Delivery from Russia to St. Petersburg. In short, wow, I did not even hope to start entertaining for holidays. In 3D print, I’m totally new, this is my first printer and tell you, I got it, connected to the outlet, connected via Wi-Fi to the computer (through the home router no additional connection). And all, already printed several models-molds for cookies. Quality I like, used branded slicer, It Free has Russian language and very simple, generates a file for the flash drive G code, or sends it to Wai Phai immediately for the memory of the printer. What else to say, stylish. Closed body, so the child of the hand could not pin, and this is very important)). In short, while there are no problems, except that it seems little filament ordered
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
I***v –
Before that, there was an enicube printer, quality compared to the sky and earth. To make the enicube less normal to print, I had to spend several dozen hours and a couple of thousand rubles on it and even after that, the printing quality is much worse than on this adventure 3. I highly recommend to buy. Maybe it will be a little more expensive than competitors, but there is something to pay for, quality printing directly from the box is worth it. The print program is very simple and visual, few people know but if desired, you can turn on a professional mode with a bunch of settings. The store is sociable, technical support at the highest level. In general, if it’s easier, consider this printer as an iPhone among 3D printers. The ship was a little dusty, because. There was no time to write a review earlier, but the quality is approximately visible, the printing is on average quality.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
N***v –
Got it in less than a week. Just pulled out of the box, just turned on the network and just started printing. The printer chose largely because that it is completely closed on all sides-for my apartment with a bunch of cats it is, perhaps, the only acceptable option is any moving device with an uncovered casing or sticking and moving wires will be the object of hunting
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
A***v –
Came very quickly
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
L***a –
Delivery mega-fast, less than 2 days in Mo. The printer prints “out of the box”. Settings are simple and understandable. Bought for a child of 10 years, liked that it is closed from all sides. So far, everything that was tried to print turned out.
Helpful(1)Unhelpful(0)You have already voted this
★★★★★
F***s –
Thanks to the store! Printing directly from the box.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
D***d –
Fast delivery, works fine. My first machine;)
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
E***v –
Ok!
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
P***i –
no camera but give diacaunt
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
M***n –
The maximum heating temperature of the extruder is 240 degrees, not all materials will fit. Nozzle diameter 0.4mm. There is a auto-calibration function, it works well. Preset modes are not bad, you can edit and/or create your presets. The native program for converting models to G-codes is not bad, not overloaded with thin settings. Very good to meet 3D printing. Technology has been very advanced in 6 years. Someone will be important: the coil from FD Plast does not get into a regular place, the diameter of the coil is more than the required.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
D***v –
I did. Better than tarantula. Size only small. Small details on it, big on tarantula.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
O***q –
Visually everything is as in the description. I will write the result later.)
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
R***r –
Everything is fine, everything works, delivery is fast, the quality of the print is decent.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
B***m –
Description corresponds. Delivered quickly, I did not even expect that they would bring so quickly. Declared the possibility of printing abs, not sure what will happen. Extruder temperature maximum 240 deg. C, for ABS is not enough, but you have to try. PLA prints without questions. The model printer itself in STL format does not recognize, you need a special. Soft (slicer) for converting models, downloaded from the official website for free. To WiFi ends, cool function.
Helpful(0)Unhelpful(0)You have already voted this
★★★★★
M***v –
The printer came fast. First there were problems with the print out of cura, but then read, that for this printer there is its own unique flashprint slicer. It is not as convenient in settings as Cura, but for beginners it is much better. There is another nuance-in the department under the coil with filament will not fit the standard coil per kilogram. It’s not very convenient, but I temporarily solved the issue with the printing of the sleeve, which puts the coil behind the body, the truth from the lid should be removed. I will still look for solutions to this issue, because small coils are not beneficial for me, and I do not like the current solution aesthetic.
V***r –
And so let’s start with the fact that the delivery is declared 30 days. So the printer came in 5 days. Delivery from Russia to St. Petersburg. In short, wow, I did not even hope to start entertaining for holidays. In 3D print, I’m totally new, this is my first printer and tell you, I got it, connected to the outlet, connected via Wi-Fi to the computer (through the home router no additional connection). And all, already printed several models-molds for cookies. Quality I like, used branded slicer, It Free has Russian language and very simple, generates a file for the flash drive G code, or sends it to Wai Phai immediately for the memory of the printer. What else to say, stylish. Closed body, so the child of the hand could not pin, and this is very important)). In short, while there are no problems, except that it seems little filament ordered
I***v –
Before that, there was an enicube printer, quality compared to the sky and earth. To make the enicube less normal to print, I had to spend several dozen hours and a couple of thousand rubles on it and even after that, the printing quality is much worse than on this adventure 3. I highly recommend to buy. Maybe it will be a little more expensive than competitors, but there is something to pay for, quality printing directly from the box is worth it. The print program is very simple and visual, few people know but if desired, you can turn on a professional mode with a bunch of settings. The store is sociable, technical support at the highest level. In general, if it’s easier, consider this printer as an iPhone among 3D printers. The ship was a little dusty, because. There was no time to write a review earlier, but the quality is approximately visible, the printing is on average quality.
N***v –
Got it in less than a week. Just pulled out of the box, just turned on the network and just started printing. The printer chose largely because that it is completely closed on all sides-for my apartment with a bunch of cats it is, perhaps, the only acceptable option is any moving device with an uncovered casing or sticking and moving wires will be the object of hunting
A***v –
Came very quickly
L***a –
Delivery mega-fast, less than 2 days in Mo. The printer prints “out of the box”. Settings are simple and understandable. Bought for a child of 10 years, liked that it is closed from all sides. So far, everything that was tried to print turned out.
F***s –
Thanks to the store! Printing directly from the box.
D***d –
Fast delivery, works fine. My first machine;)
E***v –
Ok!
P***i –
no camera but give diacaunt
M***n –
The maximum heating temperature of the extruder is 240 degrees, not all materials will fit. Nozzle diameter 0.4mm. There is a auto-calibration function, it works well. Preset modes are not bad, you can edit and/or create your presets. The native program for converting models to G-codes is not bad, not overloaded with thin settings. Very good to meet 3D printing. Technology has been very advanced in 6 years. Someone will be important: the coil from FD Plast does not get into a regular place, the diameter of the coil is more than the required.
D***v –
I did. Better than tarantula. Size only small. Small details on it, big on tarantula.
O***q –
Visually everything is as in the description. I will write the result later.)
R***r –
Everything is fine, everything works, delivery is fast, the quality of the print is decent.
B***m –
Description corresponds. Delivered quickly, I did not even expect that they would bring so quickly. Declared the possibility of printing abs, not sure what will happen. Extruder temperature maximum 240 deg. C, for ABS is not enough, but you have to try. PLA prints without questions. The model printer itself in STL format does not recognize, you need a special. Soft (slicer) for converting models, downloaded from the official website for free. To WiFi ends, cool function.
M***v –
The printer came fast. First there were problems with the print out of cura, but then read, that for this printer there is its own unique flashprint slicer. It is not as convenient in settings as Cura, but for beginners it is much better. There is another nuance-in the department under the coil with filament will not fit the standard coil per kilogram. It’s not very convenient, but I temporarily solved the issue with the printing of the sleeve, which puts the coil behind the body, the truth from the lid should be removed. I will still look for solutions to this issue, because small coils are not beneficial for me, and I do not like the current solution aesthetic.
I***a –
Very precise
D***t –
All right. All right.